Redline Handle Tools

Malco's 5 Blade Sheet Metal Crimper set in front of a black background

5-Blade Sheet Metal Crimper

The five blades on the Malco C5R allows maximum crimping power, producing a 1-5/8 inch (41.3 mm) long, shallow, double crimp that replicates factory indentations and ensures a tight fitting, leak-proof connection.


Malco C6R Offset 5 Blade Sheet Metal Crimper

5-Blade Offset Sheet Metal Crimper

The offset sheet metal crimper is an ergonomic solution that is ideal for tight working quarters or working over-head.


Malco SC3R Sheet Metal Crimper

3-Blade Sheet Metal Crimper

Downsizes heavy stove pipe and round metal duct to create a male connection for joining sections.


Malco's J-Channel Cutter for Vinyl Siding

J-Channel Cutters

Makes drain tabs, downstream notch cutouts and miter trim cuts for vinyl siding J-Channel.


Nail Hole Punch, Vinyl

Makes a horizontal slot for adding or elongating nail holes in vinyl or aluminum siding to accommodate stud spacing.


Malco SL8R Vinyl Siding Snap Lock Punch

Snap Lock Punch for Vinyl Siding

The Vinyl Siding Snap Lock Punch Produces wider, more prominent rectangular tab projections for securing vinyl skirting or siding to finishing trim.


Malco Ceiling Grid Punch

Ceiling Grid Punch

Accesses tight corners to make 1/8 inch (3.2 mm) rivet holes in up to three layers of 25 gauge (0.53 mm) tees and angles.


Punch Lock, Metal Stud Crimper

Secures metal stud and runner without fasteners. Squeeze handles together with one hand while holding stud in place.


Gutter end cap crimper by Malco

Gutter End Cap Crimper (Adjustable Snap Lock Punch)

Ideal gutter tool to use for crimping end caps in place. Also creates locking tabs in light sheet metals.


Worker with gloved hands using Malco's C4R Gutter Tool to crimp a white downspout

5-Blade Gutter Downspout Crimper

Produces an effective double crimp that downsizes corners of aluminum or steel downspout. Crimps made by the tool help create a connection that is more self-supporting during gutter installation.


Malco's Fiber Cement board Snip with handles and jaws open

Fiber Cement Siding Snip

For precise arc and trim cuts in 5/16 inch (7.9 mm) fiber cement siding plank fast and easy.


Vinyl Fence Notcher next to two pieces of notched vinyl fence posts

Vinyl Fence Hand Notcher – 1/2″ and 3/4″

Creates 1/2 and 3/4 inch (19.1 mm) wide, 7/8 inch (22.2 mm) deep louver-shaped tabs to lock vinyl pickets and rails in place.


Hand Seamers with Forged Jaws

For bending metal and flattening seams, as well as straightening sheet metal or safely gripping and moving metal on the job.


Hand Seamers with Cast Zinc Jaws

For bending, seaming and straightening non-ferrous metals and limited flattening/straightening applications in light gauge steel.


PEX To Wire Tool

Labor-saving way to layout an in-floor radiant heating system on a wire grid.


Malco N1R Sheet Metal Notcher

Hand Notcher – 13/16 Inch and 1 Inch

Model N1R for metal duct corner notches and take-off tabs makes a clean 30° “V” shaped cut in 24-gauge (0.71 mm) galvanized steel. Model N2R for metal duct corner notches makes a clean 1-inch deep “V” shaped cut in 24-gauge (0.71 mm) galvanized or (0.61 mm) mild steel.


Hole Punch – Sheet Metal, Vinyl Plastic

Use for edge hole applications in sheet metal or vinyl plastic including metal ductwork and vinyl window extrusions.


Malco SL1R Sheet Metal Snap Lock Punch

Snap Lock Punch for Sheet Metal

Raises a projection along edge of sheet metal for locking into rolled edge of sheet to be joined.