MalcoEdgeâ„¢ Elite Flow 8.9 A1/A2L/A3 Vacuum Pump (EF89)

The Where To Buy map requires marketing cookies to be accepted. Please change your cookie preferences by clicking here and accepting cookies.


The MalcoEdgeâ„¢ Elite Flow 8.9 Vacuum Pump is built to evacuate larger residential and commercial systems to a deep vacuum faster than smaller 5 or 6 CFM pumps. It has an 8.9 CFM flow rate and reaches an ultimate vacuum of 15 microns with a 2/3 HP motor running on 115V 60Hz power. For use on A1, A2L, and A3 systems.

A large 1/2 in. inlet port, plus 3/8 in. and 1/4 in. connections, makes it easy to add a high-flow Y and multiple hoses for faster evacuation. An integrated auto-shutoff solenoid prevents vacuum loss and pump oil backflow if power is interrupted.

The oil reservoir holds 20.9 fl oz (620 ml) and the power cord is 16.4 ft (5 m). Dry weight, without oil, is 35.25 lbs (15.9 kg), and the pump measures 11 in. x 16 in. x 6.5 in.. Operating environment is 41°F to 104°F (5 to 40°C).

Best suited to split systems and larger commercial systems with accessible locations. Not for use with ammonia systems.  

Features

  • 8.9 CFM flow rate pulls bigger residential and commercial systems down to deep vacuum faster than 5 or 6 CFM pumps
  • For use on A1, A2L, and A3 systems
  • 15 micron ultimate vacuum with a 2/3 HP motor on 115V 60Hz power
  • Built-in auto-shutoff solenoid stops pump oil backflow and vacuum loss during a power disruption
  • 1/2 in., 3/8 in. and 1/4 in. hose connection points; the large 1/2 in. inlet takes a high-flow Y plus multiple hoses
  • 20.9 fl oz (620 ml) oil reservoir and 16.4 ft (5 m) power cord
  • Sized for split systems and bigger commercial systems; not intended for ammonia systems

FAQs

Q1: Can I recover refrigerant from a system with the MalcoEdge Elite Flow Vacuum Pump?

A1: We do not recommend using a vacuum pump for recovery. Specialized, UL-tested recovery machines are required for refrigerant recovery. MalcoEdge offers the MERU1 and MERU2 recovery machines for this purpose.

Q2: How do microns compare to PSI?

A2: 0.000019337 PSIG = 1 micron of mercury (if you get under 500 microns, you are dealing with a deep vacuum)

Q3: What are the differences between a recovery machine and a vacuum pump? Are they used for the same tasks or for separate tasks when servicing an HVAC/R system?

A3: The MalcoEdge recovery machine removes liquid and vapor refrigerant from a system for reuse, recycling, or reclamation. Recovery machines must be UL-tested and rated for recovery rates and safety, and they include specialized features to aid in filling a recovery tank and avoiding overfilling it. A recovery machine does not typically draw a system into a deep vacuum. A MalcoEdge vacuum pump, on the other hand, removes any residual vapor, moisture, and noncondensibles from a system and draws the system down into a deep vacuum to prepare it for charging. A vacuum pump would also be used to perform a decay test.

Q4: What does BL stand for when discussing MalcoEdge vacuum pumps?

A4: BL stands for brushless motor. Brushless motors are also sparkless motors, making them safer to use around potentially flammable refrigerants.

Q5: What micron level should I be drawing my HVAC systems down to?

A5: We recommend referring to the equipment manufacturer for the target vacuum range. Some of our vacuum pumps can pull systems down to 15 microns, but many manufacturers recommend a minimum of either 300 or 500 microns.

Q6: What happens if I am pulling a vacuum on a system and the power goes out?

A6: MalcoEdge vacuum pumps have a solenoid valve that seals off the system if there is a loss of power. When power is restored, the valve will automatically release and the pump will continue to run to pull the system into a deeper vacuum.

Q7: How often should I replace my vacuum pump oil?

A7: We recommend changing your oil every time you draw down a system or notice that the oil is dirty. We recommend MalcoEdge oil, available in 1-quart (VPOQ) or 1-gallon (VPOG) packages.

Q8: I am having a difficult time reaching peak vacuum. Is there anything I should check before leak checking the system I am attempting to draw down?

A8: Verify that the oil is clean. Dirty oil will limit the vacuum you can pull with the pump. You can also recheck all of your hose and fitting connections to be sure they are tight and not introducing potential leak points. As a last resort, you can verify that your vacuum pump is pulling to a deep vacuum at the pump by valving off the pump from the system and attaching a micron gauge directly to the pump’s 1/4″ port.

Q9: Do you offer a quick-change oil system for MalcoEdge vacuum pumps?

A9: No, a quick-change oil system is not offered.

Q10: Do you offer pre-measured oil for your vacuum pumps?

A10: MalcoEdge oil is available in 1-quart (VPOQ) or 1-gallon (VPOG) packages. It is not offered premeasured.

Q11: What is your warranty for MalcoEdge recovery machines and vacuum pumps?

A11: MalcoEdge recovery machines and vacuum pumps include a 1-year standard manufacturer’s warranty. The warranty extends to 3 years if the end user registers the product at purchase. See Malco’s website (link to product registration page) for additional information.

Q12: What is the achievable minimum vacuum?

A12: 15 microns

Downloads

My Review for MalcoEdgeâ„¢ Elite Flow 8.9 A1/A2L/A3 Vacuum Pump (EF89)

  • This field is for validation purposes and should be left unchanged.